Name/Description:

Item #:

Category:
Primary Color:
Loudness:
Primary Effect:
Price:
   Clear Form



*not all items available in all locations

PRODUCT CATALOG : FIREWORKS IGNITOR SYSTEM : INSTRUCTIONS

1. Illustration 1 shows the correct way to connect the clip of an E-fuse to the tip of an individual firework fuse

2. Place the fireworks on the ground* in order, making sure they are standing securely and cannot fall over. Separate the clips and split the cable into single strips of wire, ensuring you have sufficient separated length to reach each of the individual fireworks. Connect each of the clips to firework fuses as shown in step 1.		 Pyro Ignitor System
3. Lift the hinged pressure switch on the top of the receiver to the uppermost position. You will be able to clearly see the ports underneath the pressure switch and the small horizontal slot for the cable to fit into.

4. Insert the integrated head of the E-fuse cable into the port slot under the pressure switch, ensuring it is fully in. Note that the UP sign on the cable must be uppermost when inserted. Press the pressure switch down fully.		 Pyro Ignitor System
5. Point the infrared receiver so that the lights are facing in the direction of where you will be standing. Press down the power switch. The two indicators will come on for a period of 12 seconds. Move to a safe distance from the fireworks with all other spectators (the system will work at a distance of 120ft, approximately 36m)

6. After a 12-second interval, the two lights on the infrared receiver will blink alternately to indicate the receiver is ready to respond to the firing signal.		 Pyro Ignitor System
7. Lock on the Fire Lock Button on the Flashlight Transmitter. The green light will illuminate to indicate the Fire Lock status is live.

8. Point the Flashlight Transmitter (from a distance of up to 120ft/36m) at the Infrared Receiver and press the Fire/Stop button. Fireworks will be immediately ignited in the sequence corresponding to the order of the clips.		 Pyro Ignitor System
9. If you wish to stop the show at any point, lock off the Fire/Stop button.

10. When the show is completed press the Fire/Stop button to halt the Receiver and finish the sequence. The system is halted when the fireworks indicator light shows off while the Power Indicator light remains on.		 Pyro Ignitor System

Sequential Fire
1. Power on Receiver (On Receiver Red and Green Lights ON).
2. Press Key #1 (On Transmitter Green Light ON).
3. After 12 seconds (On Receiver Red and Green Lights flash alternatively), point Transmitter at Receiver (from a distance of up to 120ft/36m) and press key #2 to ignite the first firework.
4. Repeat step 3 to ignite left fireworks, then Receiver halted (On Receiver Red Light ON and Green Light OFF).

Rapid Fire
1. Power on Receiver (On Receiver Red and Green Lights ON).
2. Within 12 seconds press Key #2 (On Receiver Red Light ON and Green Light OFF).
3. In the next 12 seconds, press Key #1 (On Transmitter Green Light ON) then key #2 three times. Release key #1 (On Transmitter Green Light OFF) and press key #2 three times (On Receiver Red and Green Lights ON).
4. Press key #1 (On Transmitter Green Light ON).
5. After 12 seconds (on Receiver Red and Green Lights flash simultaneously), point Transmitter at Receiver (from a distance of up to 120ft/36m) and press key #2 to ignite all fireworks.

Note:
1. It is not advisable to use the system in daylight as the product can be affected by sunlight.
2. Do not connect flat cable to receiver until after you have connected fuses to fireworks and make sure power to the receiver is off when connecting cable to receiver.
3. The system will automatically halt if there is no operation within 6 minutes.
4. E-Fuses can only be used once. Additional fuses can be purchased separately.

*Please Note: E-Fuses can only be used once. Additional fuses can be bought separately.

Frequently Asked Questions





















B.J. ALAN COMPANY (Sitemap)
Copyright © 2008 B.J. Alan Company. All rights reserved.
Web Design & Web Development by Aristotle